Starterkit armStone™A9/r3 Linux

The armStone™A9/r3 in PicoITX format has standard connectors for 10/ 100/ 1000 Ethernet, 2x USB Host, USB Device, as well as Audio Line Out, DVI, SATA, and on the bottom side mPCIe. A power plug was assembled to supply the board with 5V. The two LVDS display channels are once on a 25pol socket and once both on a JILI30 connector (for dual channel LVDS). The alternative RGB display interface is on a 34-pole ESCDI interface. The resistive touch or capacitive touch controller (I²C) is connected via another 6-pole socket or the ESCDI display adapter. A USB Host interface is located on a 4-pole pin strip. Further interfaces are found on J1, and a 10-pole pin strip was already equipped for COM1.

The armStone™A9/r3 starter kit consists of the armStoneA9/r3-V1-LIN (with 1GB RAM, 128MB Flash, Audio, Ethernet, CAN, PCIe, SATA, and a resistive touch controller on the display adapter). Furthermore, we have equipped the RGB interface (34-pole ESCDI), as well as both LVDS interfaces.

One can connect an RGB display and two LVDS displays simultaneously. A bootloader and a Linux Image are already pre-installed.

The scope of delivery of the starter kit contains an additional cable set, a 7" WVGA TFT with a resistive touch panel, and the fitting display adapter with film cable. On a supplement, you can find the access data to documentation and software.
The starter kit also comes with a finned heat sink on the CPU, please note that these finned heat sinks are not contained in volume deliveries.

Additionally, we offer a 4-hour Workshop. The goal of the workshop is, to learn how to handle the armStone™A9/r3 starter kit and complete it with a running system. Under Linux, you learn how to deal with Buildroot and further Linux tools.

• Scope of Delivery
• Accessories

Scope of Delivery

aStoneA9/r3-V1-LIN
NXP i.MX 6Quad Cortex-A9, 1GB RAM, 256MB Flash, Gb Ethernet, CAN, Audio, PCIe, SATA, Touch, RGB, LVDS, DVI, 0°C-+70°C, 5V Supply, Linux Buildroot/Yocto
SKU: aStoneA9/r3-V1-LIN

Displaykit RGB 2
7" WVGA Display with RGB interface and touch panel, connection cable (40pol film cable), display adapter and touch cable
SKU: aSt-RGBKIT

Produkt SINTF-CABKIT nicht vorhanden

Power Adapter
To supply armStone™ and PicoCore™ modules with 24V.
SKU: ADP-NT24V3

Software 

	Secure Boot as a Service The SBS (Secure Boot as a Service) includes the signing (protection against manipulation) and if necessary encryption (protection of intellectual property) by F&S Elektronik Systeme. SKU: Linux-SBS	500,- €
	Display Customization (RGB or LVDS display under Linux) Creation of a DeviceTree (Buildroot or Yocto) for your F&S Board. The DeviceTree contains the appropriate entries for your display. SKU: EW-SW	700,- €
	Display Customization (MIPI-DSI Display under Linux) Creation of a DeviceTree / kernel (Buildroot or Yocto) for your F&S Board. The DeviceTree / kernel contains the appropriate entries for your MIPI-DSI display. SKU: EW-SW-MIPI-DSI-Linux	1,000,- €

Displays and Display Kits

	7" RGB Display with resistive Touch 7" TFT (800x480) EDT ET070080DH6 SKU: B.LCD.15	120,- €
	7" RGB Display with PCAP Touch 7" TFT (800x480) Display Endrich MI0700AJT-54CP with capacitive Touch SKU: B.LCD.18	150,- €
	Displaykit 7" RGB - PCAP Touch 7" Display with RGB interface and capacitive touch panel, connection cable (50pol film cable) and display adapter. SKU: KIT-TFT-7RGB	210,- €
	Displaykit RGB 2 7" WVGA Display with RGB interface and touch panel, connection cable (40pol film cable), display adapter and touch cable SKU: aSt-RGBKIT	170,- €

Touch Kits

	Resistive Touch Kit 2 For the connection of a resistive touch panel to boards with 6pol Hirose socket. SKU: SINTF-ADP-RTI2C	Request
	PCAP Touch Kit for EDT Kit to connect an EDT PCAP touch panel SKU: ADP-EDTTOUCH2	35,- €

Cables

	50poles Film Cable Cable for 7" RGB Endrich Display (B.LCD.18) FFC cable, A50pol., pitch=0,5mm, l=200mm SKU: B.MKAB.41	10,- €
	LVDS Cable LVDS cable with JAE FI X30 on one side and open ends on the other side SKU: B.MKAB.53	22,- €

Adapters

	I2C Erweiterung Circuit for an external extension with GPIOs, AID, PWM and matrix keyboard. This external circuit is connected via I²C Bus. SKU: NDCU-ADP/I2C	80,- €
	armStone™ Extension Routes interfaces of the 66pin feature connector to standard connectors. SKU: aStone-ADP-UNI1	130,- €
	armStone™/ efus™/ PicoCore™ DVI Adapter Connects armStone™, efus™ or PicoCore™ to a DVI/ HDMI screen. SKU: aStone-ADP-DVI	50,- €
	Adapter for Endrich iSi50 Displays Adapter to connect Endrich iSi50 displays to F&S boards SKU: aSt-ADP-MIT1	50,- €
	JTAG Debug Adapter To program Cortex-M4. SKU: ADP-CMSIS	69,- €
	Power Adapter To supply armStone™ and PicoCore™ modules with 24V. SKU: ADP-NT24V3	40,- €
	mPCIe Module with WLAN/BT mPCIe-Full-Mini Type F1 or mPCIe-Half-Mini Type H1 module with WLAN 2.4/ 5 GHz und BT5.0 LE SKU: ADP-mPCIe-WLAN	40,- €

Workshops

	Workshops Workshops for F&S Boards with Windows Embedded Compact or Linux - Beginner Workshops - Qt 5 - Asymmetric Multiprocessing - Secure Boot SKU: NDCU-WS1	Request
	Secure Boot as a Package Secure Boot as a Package contains a workshop, where you learn how to realize the topic Secure Boot. You will also receive a user Tool Software. SKU: WS-SBP	500,- €

Other Accessories

USB Stick USB Memory Stick with common memory size (2GB+) and imprinted F&S logo. The USB Stick was tested on all current F&S boards. SKU: USBSTICK.1

20,- €